产品中心
2048L InGaAs 线扫描相机 | GL2048L

高分辨率线扫描Sensors Unlimited 2048L提供方形像素(10 x 10 μm)用于机器视觉或高像素(10 x 210 μm),以便于与光谱仪对齐。 这些摄像机通过提供灵活性的Base Camera Link®接口提供每秒100到>76,000的线速。

产品特点
· 2048 x 1 像素阵列,10 µm 间距
· 方形 (10x10 μm) 或高 (10x210 μm) 像素选项
· 从 0.98 μm 到 1.65 μm 的高 QE(量子效率)
· 具有快照曝光功能的固态 FPA
· 用户控制的曝光和线周期
· 线路速率从每秒 0.1 k 到 76 k 行
· >1200 : 1 高增益动态范围
· 4 种灵敏度选择
· 通过Camera Link CC1线外部触发线和曝光
· 封闭体 < 136 cm3 (< 8.3 in3 )
· 低功率 < 3.6 W 超过 6-12 V
· 获取并保存用户非均匀性校正
· Base12 位 Camera Link® 接口
· 满足 FCC 和 CE 对辐射和传导发射、此类发射的抗扰性和 ESD 抗性的要求
· GL2048 相机符合欧盟 RoHS 和指令
· GL2048 相机符合欧盟 RoHS 和指令
典型应用
· 光学相干断层扫描:1.04、1.31、1.55 µm
· 0.94 至 1.68 µm 波长范围内瞬态光谱的高分辨率光谱
· 硅晶片或集成电路显微镜
· 移动物体的 SWIR 机器视觉 (MV)
· 热 MV 成像 > 150 °C 通过玻璃窗
产品介绍

高分辨率线扫描Sensors Unlimited 2048L提供方形像素(10 x 10 μm)用于机器视觉或高像素(10 x 210 μm),以便于与光谱仪对齐。 这些摄像机通过提供灵活性的Base Camera Link®接口提供每秒100到>76,000的线速。2048提供光学相干断层扫描(OCT)或工业机器视觉所需的高分辨率、稳定性和可靠性。 在0.98至1.65 μm的短波红外(SWIR)波长范围内提供高均匀灵敏度。 对所有像素的同时采集提供了重要的医疗和工业机器视觉所需的卓越的可重复性和较长的工作寿命。

GL2048L | QE(量子效率)

产品型号及主要指标


OPTO-ELECTRONIC PERFORMANCE

Sensor format 1

2048 pixels with 2048 readout ADCs on 10 µm pitch

Optical aperature (pixel height)1

210 µm or 10 µm

Quantum efficency1

> 60% over 0.98 µm-1.65 µm; > 70% peak response @ 1.55 µm


Gain setting

Temporal noise (rms counts)1 2

High

Medium High

Medium Low

Low

Typical

Specification

Typical

Specification

Typical

Specification

Typical

Specification

3.1

< 3.4

2.2

< 2.8

1.9

< 2.3

1.7

< 1.9

Dynamic range1,2


> 1200:1


> 1450:1


> 1750:1


> 2100:1

Differential non-linearity1,2

+/- 1.1

< +/- 2.5%

+/- 1.5

< +/- 2.5%

+/- 1.5

< +/- 2.5%

+/- 1.5

< +/- 2.5%

Bad pixel specification

White, dark, noisy or pixels exceeding +/- 20 % of the mean value when illuminated at 50% of full well. 

Number of bad pixels limited to a maximum of 1% of array total; on-board pixel replacement function

Exposure time1,3

5.5 µs to 10 ms, user programmed in pixel clock cycles or via the width of the ext. trigger

Trigger modes 3

Free run, single line per trigger (exposure set by camera), or variable exposure

External trigger 3

Via CC1 signal line in Camera Link cable

External variable ET

User set by the duration of trigger input signal (minimum exposure time pulse: 5.5 µs)

External trigger jitter

+/-2.5 clock cycles: nominally 63 ns variation

Pixel rate

2048L:157 Mpix/s with 2 x 12-bit words transferred on each Camera Link strobe clock at 80 MHz

Digital output format

12-bit base Camera Link®; 

recommend NI PCIe-1433 or frame grabber with throughput of > 313 Mbytes/s to PC motherboard

 (minimum of 4 bi-directional PCIe express lanes in PC)

Readout mode

Integrate-While-Read, differential double sampling

Corrections (preset OPR)

Factory calibrated gain, offset, and bad pixel replace.

 1 Actual formats and performance governed by pixel size options (dark current may limit longest usable ET, especially at high gain);

2 Camera readout noise limited for low & medium gain settings; dark shot noise limited for high gain settings at longer exposure times

3 Modes are user selectable by command over Camera Link® serial lines


INTERFACES

Control: & Data

GL2048L: Single SDR 26-pin connector

Power Connector

CUI Inc. PJ-056, 1.0mm X 3.8mm power jack

Trigger: Input

Via Camera Link CC1 line

Status LED:

Green: Power on

Tested Framegrabbers

Nat. Instruments PCIe-1429, -1433, Matrox Solios eV-CL PCIe-X4

 *

REGULATORY COMPLIANCE

CE:

Meets class A for emission, immunity & ESD standards, RoHS

FCC:

Meets requirements for Part 15, Subpart B, Class A, 2006

 *

ENVIRONMENTAL & POWER

Operating Case Temperature

+10°C to +35°C

Storage Temperature

-10°C to 60°C

Humidity

Up to 95% and non-condensing

Power Requirements:
AC Adapter Supplied
DC Voltage
Typical Power

100–240 VAC, 47–63 Hz
+6 to 12 VDC (Maximum: 13.1 VDC)
3.6 W at 30°C case temp1

In-rush Current

1.25 A @ 12 VDC

 *

MECHANICAL

Width x Height x Depth:

8.3 cm x 10.2 cm x 1.6 cm (excludes I/O connectors, and lens adapter)
3.25 in x 4 in x 0.64 in (excludes I/O connectors, and lens adapter)

Weight:

< 240 g or 8.6 oz (no lens or adapter)

Threaded Lens Mount

M42x1-6H (focus point ~6 mm from camera surface)

Optional Lens Mount Adapters

C-Mount adapter or adjustable distance F-Mount adapter (see ordering info)

Spectrometer Mount

4 tapped 8-32 holes in 2 inch square pattern,
2 tapped 8-32 holes in-line with image axis,
O-Ring light seal, 1.9 inch diameter, 1/16th thickness

Camera Tripod
Mount

2 tapped¼-20 holes, one on bottom, one on side wall.

 *

ORDERING INFORMATION

Camera Model

Part number

Max. Line rate

Pitch

Pixels

FPA length

Aperture (height)

Classification

GL2048L-10A-ENC-STD-210

8000-0596

76,263 lps

10 μm

2048

20.48 mm

210 μm

EAR99

GL2048L-10A-ENC-STD-010

8000-0597

76,263 lps

10µm

2048

20.48 mm

10 µm

6A003.b.4.a

Included items in qty 1-4: Power supply, lens cap, ESD foam-lined shipping box, mini-CD with manual and SUI Image Analysis software for National Instruments IMAQ environment.

Order lens adapters separately for additional charge:

Part Numbers: Adjustable F-mount adapter: 8000-0171. C-mount adapter: 3800-0002

SUI’s linescan cameras, accessories, and associated technical data are subject to the controls of the Export Administration Regulations(EAR). Export, re-export or transfer of these items by any means to a foreign person or entity, whether in the United States or abroad, without appropriate Department of Commerce authorization, is prohibited and may result in substantial penalties.

相关产品
在线留言
导航 产品 资料 电话